Specification:
Brand: GEELANG
Item Name: LIGO78X 78mm Ducted Cinewhoop Drone BNF
Wheelbase: 78mm
Size: 119x132x23mm(Camera mount not included)
Weight: 72g (Camera mount not included)
Weight: 136g (With 3S 450 Battery, 360GO thumb camera )
Flight Controller
|
Item Name: SH50AF4 MATEKF411
MCU: STM32F411CEU6 (100MHz, 512K Flash Memory)
Sensor: MPU-6000 (SPI Connection)
Built-in 5A (Each) Blheli_S 4 in 1 ESC Dshot600 Ready
Built-in Betaflight OSD (SPI Control)
Built-in 5V 2A BEC
Built-in Voltage Detection
Shop: 8MB Black Box Onboard
Power Supply: 2-3S Battery Input (DC 7-12.6V)
Board Size: 28.5 * 28.5mm
|
Onboard 4 In 1 ESC
|
Onboard 4 In 1 ESC MCU Upgraded to EFM8BB21
Power Supply: 1-2S LiPo/LiPo HV (3.5V/8.7V) Current: 5A Continuous Peak 7A (3 Seconds) Support BLHeli_Suite Programmable Factory Firmware: S_H_50_REV16_77.HEX
Default Protocol: DSHOT300
Power Input: XT30
|
Motor
|
Item Name: GL1202 8700KV
Stator Specifications: D12 * H4 0.2mm
Configu-ration: 9N12P
Stator Diamter: 12mm
Stator Length: 2mm
Shaft Diameter: Φ1.5mm
Winding Specifications: 180℃ Class Multiple oxygen-free copper
Weight(g): 3.4g
No.of Cells(Lipo): 2S-3S
|
Frsky NON- EU XM+
Receiver Version
|
SBUS Receiver
Frsky D8/D16 Switchable
Compatible Non EU Transmitter both D8 and D16 mode
Channels: 8CH / 16CH
Failsafe Support
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
Operating Voltage Range: 3.7~10V Operating Current: 30mA @5V Operating Range: Full Range With RSSI Output on Board: Analog 0~3.3V Firmware upgrade-able, can be upgrade to EU-LBT with RSSI
|
Compatible Flysky Receiver Version
|
IBUS Receiver
Protocol: AFHDS-2A
Channels: 14CH (AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
Failsafe Support
|
Compatible DSMX Receiver Version
|
Serial Bus Receiver
Protocol: DSM2/DSMX Compatible
Channels:6-9CH (Depend on your radio)
No ground interference ( Transmitter and receiver 1 m from the ground): 300m
|
TBS NANO
Receiver Version
|
CRSF Protocol , Official TBS transmitter compatible
Protocol: CRSF
Channels: 8CH
Failsafe Support
Support receiver hardware rssi function
No ground interference ( Transmitter and receiver 1 m from the ground): 500m
|
PNP Receiver Version
|
Support any bus and other protocols, users can install by themselves
|
5.8G VTX
|
Power Switching: Third Gear(25MW , 100MW , 200MW)
Frequency: 40CH Input Voltage: 3.3V 5.5V Current Consumption: 300mA (Type) Frequency: 5.8GHz 5bands 40 channels With Raceband
Smartaudio ready(Frsky EU-LBT and DSMX version not compatible) Weight: 2.0g
|
Camera |
GL950PRO: 1/4 COMS Sensor
Horizontal: 800TVL 800×600
TV System: Ntsc 4:3 non-changeable
Power Input: DC 5-12V
FOV: F1.2
Colorful: 0.1Lux(F1.2,50IRE,AGC ON)
Black and white: 0.01Lux(F1.2,50IRE,AGC ON) Signal to Noise Ratio > 50dB Dynamic Range >60dB
Lens: m7
White Balance: Auto white balance
Image: Color
BLC: Stand by
Video Format: NTSC
Weight: 1.5g
|
Propeller |
Gemfan 2023-3 Toothpick Props
Material: PC
Weight: 0.88g
Pitch: 2.3 Inch
Props Dia: 52.17mm
Center Thickness: 5mm
Center Hole Dia: 1.5mm 3 holes
|
Battery Recommended
|
Species: lipo, lipoHV
Capacity: 450-550mAh Voltage: 7.8-11.1 Continuous Discharge Rate: 60C Instantaneous Discharge Rate: 80C Connector: XT30
|
Features:
1. Use SH-50A flight controller to support 2-3s lithium battery power supply. The integrated Betaflight OSD function keeps track of the signal of the flight voltage receiver and can observe the status in real time during flight.
2. VTX comes with Smartaudio function, you can adjust the flight control parameters through the OSD, adjust the flight control PID, and adjust the VTX frequency point parameters Completely assembled and debugged, you can fly with the remote control.
3. A more compact design is adopted for the first time, with a wheelbase of 78mm. However, passing long-term flight tests will not affect flight efficiency at all. Indoor flight has better maneuverability and playability.The FPV end adopts GL950 camera, the image quality is clear. The complex environment of flying indoors has better observation and controllability.
4. The 3s power supply and the 2-inch three-blade propeller have been tested and matched for a long time, and have obtained good operability and durability. It is recommended to use 3s 450mah battery, if you need longer space, you can add 3s550mah battery. Through continuous improvement, the problem of low efficiency of the 2-inch air duct machine was finally solved. Indoor small cross aerial photography becomes a reality. In order to better protect the outer ring,EVA sponge material is used to improve safety and reduce wind resistance. Through optimization, the performance is very good.
5. The flight controller supports Betaflight adjustment, a variety of flight modes, carefully adjusted by the original factory, suitable for novice flight practice, stable style.
6. Independent use of multiple versions of the receiver, electronic control is more stable. The flight control adopts the newer version of Betaflight 4.2, and the ESC adopts the 16.77 version. Both the two-way DSHOT mode and the gyroscope RPM filter are turned on to make the flight control more stable.
7. The weight of the whole machine is controlled at 72g, which solves the weight problem of the traditional air duct machine and is flexible in control.
8. The original factory is equipped with two sets of 360go thumb camera mounts, which can be replaced as needed.
9. The tail RGB LED flight control can be adjusted freely.
Package Included:
1 X GEELANG LIGO78X 2.3 Inch 78mm Wheelbase FPV Racing Drone
2 X 3D Printed 360gGO Thumb Camera Bracket Red & Blue
4 X GL1202 KV8700 Motor
8 X 2023 Propeller (4CW+4CCW)
1 X 5.8G VTX5840
1 X RGB LED
1 X GL950 Camera
1 X Screwdriver Removal Tool
2 X Battery Magic Strap
1 X High-end Paper Box
1 X USB Cable
1 X 3S 450mAh LipoHV Battery
Option 1: SH50AF4 Frsky NON-EU XM+ Receiver Version
Option 2: SH50AF4 Flysky Receiver Version
Option 3: SH50AF4 DSMX Receiver Version
Option 4: SH50AF4 TBS Crossfire NANO Receiver Version
Option 5: SH50AF4 PNP NO RX Receiver Version
Reviews
There are no reviews yet.