Overview:
The XKC-C352 high and low liquid level controller can be used in conjunction with the XCK-Y25 non-contact liquid level sensor, or it can be used with other liquid level sensors such as floats to realize the low liquid level alarm sent by the liquid level sensor when the container liquid level is too low When the signal is signaled, the water pump automatically starts to add the liquid level, and when the liquid level reaches a certain height, the high liquid level sensor sends a signal to automatically stop the water pump, thereby realizing the automatic control function of the container liquid level. The controller has strong self-check protection ability, with water pump dry stop detection, high overflow detection, pumping overtime detection; diversified control, can control the pump in manual mode, or control the pump in automatic mode; multiple output modes, one load output, high control power It can reach 1600W, one alarm output control can reach 800W, there is a relay normally open output, and it can also output 110V or 220V. The controller has comprehensive functions and is suitable for a variety of applications.
Features:
1. Strong compatibility, can use a variety of liquid level sensor input control;
2. Strong protection, with waterproof pump idling protection and water level overflow detection output, with 4 hours overtime pumping alarm;
3. Relay dry node output, suitable for multiple load control;
4. The control is diversified, and the pump can be controlled in manual or automatic mode;
5. The installation is simple and convenient. It can be installed with screws or electric box tracks;
Electrical parameters:
|
Model
|
XKC-C352-3P
|
Name
|
C352 High and low liquid level automatic controller
|
|
Input Voltage
|
AC100V-220V 50/60Hz
|
|
working voltage
|
DC12V
|
|
Working current
|
Working current≤110 mA, Static current consumption≤20mA
|
|
Load power
|
1.6KW following（Overload or for three-phase water pump need to install AC contactor）
|
|
Alarm output
|
800W（Resistive load）Normally open normally closed output
|
|
Output mode
|
The relay is normally open or closed or ACAC110V/220V two types 2Select one output
|
|
Input signal
|
Low inductive signal input;
High induction signal input;
Pump idling detection signal input;
Water overflow alarm signal input;
|
|
Interface voltage of induction head
|
DC 12V
|
|
working temperature
|
-10~75℃
|
|
Dimensions
|
115*90*40MM
|
Corresponding diagram of signal input and relay output:
|
Input signal
|
Load output
|
|
Alarm signal status
|
Alarm output
|
|
The low order is 0, The high order is 0
|
Normally open and closed, Normally closed open
|
Follow
ring
|
The low order is 0, The high order is 1
|
Normally open and closed, Normally closed open
|
|
The low order is 1, The high order is 0
|
Normally open and closed, Normally closed open
|
High overflow is 1
|
Normally open and closed, Normally closed open
|
|
The low order is 1, The high order is 1
|
Normally open, Normally closed
|
call the police state, Load output: Normally open, Normally closed
（Relay off status, Load break in protection）
|
|
The low order is 1, The high order is 0
|
Normally open, Normally closed
|
|
The influent water was detected as 0 Time
|
Normally open, Normally closed（Relay off status, Load break in protection）
|
Basic function introduction:
1. Automatic water level control: the water level is lower than the low level sensor probe, the water pump is automatically started, the water level rises to the high level, and the water pump is automatically turned off.
2. Idling delay pump stop: If it is detected that there is no water in the water supply pipe after starting, the pump will be turned off after a delay of 3 to 5 minutes. During the pumping process, if the water flow is interrupted for more than 3 seconds, the water pump should be shut off immediately.
3. Automatic tracking of water source: After idling stop the pump, start the water pump to pump water every two hours until the water is full and stop the pump.
4. Pumping overtime protection: continuous automatic pumping for more than 5 hours, automatically stop the pump. The work indicator flashes quickly, you can press the K2 button to stop, or automatically delay to resume standby.
5. Manual automatic switching: The controller enters the automatic working mode by default when it is turned on. Press the K1 key to switch the working mode. The red light is on for automatic mode, and the red light is off for manual mode.
6. Non-contact sensing probe: Adopting non-contact capacitive sensing technology and special sensing control chip design, the probe has durability, strong anti-interference ability, sensitive induction, no contact with liquid, corrosion resistance, safety and environmental protection without pollution.
Package included:
1 X Water Level Switch Controller
Availability: 
Shipping: Free Airmail 
Reviews
There are no reviews yet.